• DESIGN AND FABRICATION OF DEMONSTRATIVE WATER JET CUTTER 

  MUHAMMAD MOIZ SIDDQUI, QAMAR ABDUL REHMAN,AHSAN SAJID (School of Mechanical & Manufacturing Engineering (SMME) , NUST, 2013)
• Design And Analysis Of Gear box for Formula Student Race car 

  Zain Fida, Muhammad Ibrahim, Muhammad Talha,Samriaz Hameed, (School of Mechanical & Manufacturing Engineering (SMME) , NUST, 2015)
• Modification Of Single Seat Race Car Engine 

  Bilal Iftikhar, Umar Janjua (School of Mechanical & Manufacturing Engineering (SMME) , NUST, 2013)
• Design & Fabrication of a Multi - Fuel Backup For Solar Water Heater 

  Taimoor Khan, Muhammad Talha Khan,M Usman Ahmed, (School of Mechanical & Manufacturing Engineering (SMME) , NUST, 2013)
• 4-DOF Robotic Arm For Industrial Automation 

  Hamza Hussain , Muhammad Haris , Osama Jarrar Haider , Muhammad Saad Bin Asif (School of Mechanical & Manufacturing Engineering (SMME) , NUST, 2024)

  This Project involves the design and development of a 4-DOF hybrid Kinematic Machine for industrial innovation. The key points about it are its light weight, high speed and high precision. This is achieved using lightweight ...
• 5-AXIS PARALLEL KINEMATIC ROBOT 

  Muhammad Hamza , Ahmed Ali Siddiqui ,Muhammad Ahsan Saleem ,Somaan Shakeel (School of Mechanical & Manufacturing Engineering (SMME) , NUST, 2024)

  Our project aims at the design and development of a 5-DOF Parallel Kinematic Robot, that will be easily programmable by an operator. The economic strength of any country is measured by the quality and speed of its production. ...
• S-D Vertical Axis Wind Turbine 

  Talha Maqsood , Huzaifa Zain, Farhan Ahmed ,Muhammad Hasnain Raza (School of Mechanical & Manufacturing Engineering (SMME), NUST, 2024)
• Design and Fabrication of Infrared Agricultural Quad-X-Copter 

  Syed Tallay Haidar, Muhammad Sharjeel Chawla,Kashif Haider,Muneeb-ur-Rehman (School of Mechanical & Manufacturing Engineering (SMME) , NUST, 2024)

  In agriculture, unmanned aerial vehicles (UAVs) are used for a variety of tasks, such as mapping, spraying, and crop monitoring. UAVs known as quadcopters are growing in popularity because of their cost, portability, and ...
• OPTIMIZATION IN DESIGN AND PERFORMANCE OF VORTEX BLADELESS WIND TURBINE 

  MUHAMMAD KHAWAR MUKHTAR, MUHAMMAD RIZWAN (School of Mechanical & Manufacturing Engineering (SMME) , NUST, 2024)

  Facing an increasing energy demand, Pakistan seeks sustainable solutions for its future, with wind energy holding significant potential. As non-renewable resources run out faster than they can be replaced, it is crucial ...
• DESIGN AND DEVELOPMENT OF A MINE DETECTION DRONE 

  Ibtesam Baig , Muhammad Ehtisham Hassan ,Ahmad Hassaan ,Muhammad Afnan Qureshi (School of Mechanical & Manufacturing Engineering (SMME) , NUST, 2024)

  In recent years, there has been a notable surge in global drone utilization, driven by escalating demand for their versatile applications, particularly within the military sector, where they are predominantly employed for ...
• Design and Development of Quadruped Robot 

  Jawad Akbar, Hinata Kashif (School of Mechanical & Manufacturing Engineering (SMME) , NUST, 2024)

  This report outlines the complete journey of designing and developing a quadruped robot, covering mechanical design, kinematic and dynamic analysis, control system development, and prototype testing. The project begins ...
• Skateboard On-Road RWD Electromotive 

  Hafiz M Hunzala Zaffar , Ali Noor Hamdani ,Syed Muhammed Ali Bukhari , Rohail Buksh, Hassan Mahmood (School of Mechanical & Manufacturing Engineering (SMME) , NUST, 2024)
• DESIGN AND DEVELOPMENT OF A SMART ROBOT FOR DISASTER RELIEF APPLICATIONS 

  KHIZAR ALI KHAN, SHEIKH MUSTAJAB AHMED , MUHAMMAD BILAL , SHAYAN KHAN MASOOD (School of Mechanical & Manufacturing Engineering (SMME) , NUST, 2024)

  This document outlines the investigation and construction of an autonomous dynamic videography rolling robot. It encompasses the examination of dynamic design principles and the selection of suitable materials for project ...
• DESIGN AND DEVELOPMENT OF AN INTERNAL PIPE INSPECTION ROBOT 

  HAMZA ZAHEER , MUHAMMAD AHMED , AKBAR KHANZADA , DANIYAL IRFAN (School of Mechanical & Manufacturing Engineering (SMME) , NUST, 2024)

  Pipelines are an integral part of the infrastructure, whether it be in Oil and Gas, Municipality or any other industry. The pipe network has increased over the past years, and increased usage has led to issues in pipelines ...
• AI-Based Solar Panel Cleaning Robot/System 

  MUHAMMAD KHAWAR , HAIDER ALI , MOHAMMAD BILAL RAZA , AHTSHAM-UL-HASSAN RIAZ (School of Mechanical & Manufacturing Engineering (SMME) , NUST, 2024)

  This project presents the design, development, and testing of a robotic system for cleaning solar panels. The primary objective was to create a robot that is highly efficient, lightweight, and cost-effective. We opted for ...
• Design and Fabrication of Variable Rate Sprayer for Agriculture Drone 

  Ahmed Hasnain Serwar , Muhammad Ehtisham Khan ,Muhammad Waseem Sajjad,Usayed Afridi (School of Mechanical & Manufacturing Engineering (SMME) , NUST, 2024)

  This report is a comprehensive study of a novel variable rate sprayer system intended for deployment on agricultural drones. The primary goal is to formulate and execute a system capable of spraying orchard spraying products ...
• Design and Manufacturing of a VIV Based Energy Harvesting Device with Multiple Cylinders 

  Muhammad Haroon , Hamza Husnain Ahmed ,Ali Abbas Khan , Mohid Qadeer (School of Mechanical & Manufacturing Engineering (SMME) , NUST, 2024)

  This project aims to harness the potential of Vortex-Induced Vibrations (VIVs) for creating an environmentally friendly electricity generation device. As global attention shifts towards renewable energy due to the rapid ...
• Desigm & Development of Collimator for X RAY Machine 

  Usama Rafiq, Muhammad Hamza Baig , Ali Zain , (School of Mechanical & Manufacturing Engineering (SMME) , NUST, 2024)

  An X-ray collimator is a device used in radiology to restrict the size and shape of the X-ray beam emitted from the X-ray tube. Its primary function is to limit the radiation exposure to the patient by reducing unnecessary ...
• AERODYNAMIC ANALYSIS OF A QUADCOPTER DRONE FOR HEAVY LOAD LIFTING 

  Muhammad Arham Khan, Rayyan Abdulaziz Bin Yasir (School of Mechanical & Manufacturing Engineering (SMME) , NUST, 2024)

  In recent years, the use of drones for package delivery has gained significant attention due to their potential to transform logistics and transportation. However, one of the major challenges in drone delivery systems is ...
• DEVELOPMENT OF A SMART METROLOGY MACHINE 

  Hafiz Abd Ur Rafay , Ezaz Ul Haq , Muhammad Ukasha , Ashar Ahmed Javed (School of Mechanical & Manufacturing Engineering (SMME) , NUST, 2024)

  In today’s landscape of modern manufacturing, stringent measures for upholding standards of quality are very important to ensure product longevity and customer satisfaction. Precision engineering demands cutting edge ...

View more