Mechanical Engineering: Recent submissions

  • Design and Fabrication of Power Kit for Wheeled Carts 
    PROJECT SUPERVISOR DR. RASHID NASEER, MUHAMMAD MUZAMMIL TALHA KHALID GULRAIZ REHMAN TAYYAB RAZA (College of Electrical and Mechanical Engineering (CEME), NUST, 2023)
    Carts are a common means of transportation for a variety of goods and materials, but when loaded with a heavy load, they can be difficult for a person to manually pull. This can be especially challenging for elderly ...
  • Design and Fabrication of Foldable and Portable Electric Bike 
    PROJECT SUPERVISOR DR. RASHID NASEER, ABDULLAH NAEEM BHATTI ALI ABID ALI AHMED MUHAMMAD DANIAL MAQBOOL (2023)
    The increasing demand for automobiles due to the growing global population has presented several challenges that need to be addressed. One major concern is the reliance on Internal Combustion Engines (ICEs) in traditional ...
  • Design of Micro Aeriel Vehicle Through Bioinspired Kinematics Using High Speed Camera 
    PROJECT SUPERVISOR DR IMRAN AKHTAR DR ZAFAR ABBAS BANGASH, DANIYAL ZIAFAT MALIK HUZAIFA SAEED MUHAMMAD USAMA MUHAMMAD TAJDAR IRFANI (College of Electrical and Mechanical Engineering (CEME), NUST, 2023)
    This paper addresses the design and development of a bio-inspired micro unmanned aerial vehicle (MAV) based on the flight kinematics of dragonflies. Dragonflies exhibit exceptional flight capabilities, including hovering, ...
  • Development of a Vehicle Longitudinal Performance Simulator 
    PROJECT SUPERVISOR DR. RAJA AMER AZIM LT COL SHAHBAZ GHANI TI(M), NS RAO MUHAMMAD ZUBAIR KHAN NS MAAZ ALI NS MUHAMMAD AKIF (2023)
    Analyzing a vehicle’s longitudinal performance during motion and studying it in terms of the engine’s output is one way of enhancing fuel efficiency of a car. The way a person drives their vehicle can affect its fuel ...
  • Development and Testing of a Noval Water Purification and Refrigeration System 
    PROJECT SUPERVISOR Dr. Abdur Rehman Mazhar, NS ALI UBAID NS SYED MUHAMMAD HAMZA SHAH NS MUNEEB ZAFAR ALVI NS SUHAIB MASOOD (College of Electrical and Mechanical Engineering (CEME), NUST, 2023)
    Water is an essential part of our lives. With the rapid increase in population and industrialization, the need for water has also increased, leading to an incremental increase in water pollution. Consumption of such ...
  • Energy Harvesting System for Highways and Railway Tracks 
    PROJECT SUPERVISOR Dr. Abdur Rehman Mazhar, NC KAINAT ALI NC EIMAN SAQIB (College of Electrical and Mechanical Engineering (CEME), NUST, 2023)
    The energy consumption in the world is increasing exponentially causing the depletion of fossil fuel-based resources. At the same time, there is extreme volatility in their prices and supply. Consequently, we must adapt ...
  • Development of Hybrid Drivetain 
    PROJECT SUPERVISOR Dr RAJA AMER AZIM, AHMAD DIN UMAR SAJJAD MUHAMMAD HARIS ARMUGHAN ULLAH (College of Electrical and Mechanical Engineering (CEME), NUST, 2023)
    Conventional ICE vehicles, while operating in urban settings, perform at very low efficiency due to inherent power characteristics Hybrid vehicles have been developed successfully to improve the engine efficiency ...
  • Design and Manufacture of Electric Powertrain for the Conversion of ICE vehicle into Full Electric Vehicle 
    PROJECT SUPERVISOR DR. RAJA AMER AZIM, MUHAMMAD HASSAN MUSTAFA MUHAMMAD SAAD IDREES MUHAMMAD HASSAN SAEED (College of Electrical and Mechanical Engineering (CEME), NUST, 2023)
    The main aim of this research is to present research findings and the work carried out related to the design of an Electric power train for front-wheel drive four-wheelers, identifying the impact that electric vehicles ...
  • Experimental Investigation of Erosive Wear of Steel For Liquid-Solid Flow 
    Project Supervisor: Dr Muhammad Rehan Khan, Muhammad Zain Muhammad Atif Shahzad Zeeshan Haider (College of Electrical and Mechanical Engineering (CEME), NUST, 2022)
    Erosion is the degradation of the flow carrying devices used in hydrocarbon and mineral process industries, especially those involved with solid particle transportation at high conveying velocities, such as many onshore ...
  • Design and Manufacturing of A Small-Scale Energy Harvesting Demonstration Model For Vibrations Lab 
    Project Supervisor: Dr. Rashid Naseer, Usama Irfan Muhammad Zubair Muhammad Ahab Sultan Asbaat Ahmad (College of Electrical and Mechanical Engineering (CEME), NUST, 2022)
    The increasing demand of energy has highlighted the exploration of alternate sources of energy. Non- renewable energy sources such as fossil fuels will run out one day. Moreover, the potential harm done to the environment ...
  • Design, Analysis and Fabrication of A Semi-Automated Medical Bed With Assisted Patient Care Transfer System 
    Project Supervisor: Asst Prof Saheeb Kiyani, Bilal Ahmed Ijaz Abdel Hameed Khalid Nawras Jehad (College of Electrical and Mechanical Engineering (CEME), NUST, 2022)
    Bed is the one piece of equipment nearly everyone working in, or using health care service will come into contact with so the right bed can enhance the quality of life of those who use them. When the patient come from ...
  • Design and Fabrication of Morphing Drone 
    Project Supervisor: Dr. Rashid Naseer, ayyab Qadeer Bilal Maqbool Sumsaam Shafiq M. Waqas Anwar (College of Electrical and Mechanical Engineering (CEME), NUST, 2022)
    This paper describes a novel quadcopter design that has the ability to morph i.e., change its shape. It uses rotary joints to quickly change the shape of its wings without the need for extra actuators. The normally rigid ...
  • Design and Fabrication of Experimental Setup To Study The Erosion of Steel By Wet Sand Particle Impact 
    Project Supervisor: Dr. Muhammad Rehan Khan, Muhammad Ali Fahad Umar Sheraz Muhammad Moin Ud Din Muhammad Abdullah (College of Electrical and Mechanical Engineering (CEME), NUST, 2022)
    Slurry erosion is responsible for major failures in oil and gas transmission pipelines. During petroleum production, sand particles can be entrained with the transported carrier fluid despite any sand exclusion process ...
  • Design and Fabrication of Semi-Automated Screen-Printing Machine For Medical Grade PVC Sheets 
    Project Supervisor: Asst. Prof. Saheeb Ahmad Kayani, Sameer Sultan Ismail Asif Danish Chaudhry Muhammad Usman (College of Electrical and Mechanical Engineering (CEME), NUST, 2022)
    Many bulk printing procedures rely heavily on-screen printing. Over the decades, a great deal of innovation has occurred, and screen printing now plays an essential role in the manufacturing, newspaper, textile, and ...
  • Design and Fabrication of Hydraulic Test Bench 
    Project Supervisor: Dr Rashid Naseer, Muhammad Asad Ur Rehman Fahad Noor Huzefa Masood Ali Ashfaq (College of Electrical and Mechanical Engineering (CEME), NUST, 2022)
    Hydraulic power control systems are a common and important part of mechanical and agricultural systems. In hydraulic power system design, power, pressure, flow rates, and mechanism of circuitry are all important factors ...
  • Design and Fabrication of Vertical Axis Wind Turbine As Micro Power Generator 
    Project Supervisor: Dr. Zafar Abbas Bangash Co-Supervisors Col Dr. Imran Akhtar, Muhammad Jayyaad Arshad Shaheer Anzak Fakhar Mahtab Shehryar Bin Shahid (College of Electrical and Mechanical Engineering (CEME), NUST, 2022)
    Energy surrounds us. Innovative energy harvesting techniques are needed to utilize this energy which would otherwise go unused. The renewable energy sources leave no carbon footprint in the atmosphere thus they are ...
  • Design and Fabrication Of 6-Axis Robotic Manipulator For Paint Application 
    Project Supervisor: Dr. Rashid Naseer, Muhammad Hassaan Zubair Ali Fazeel Jamil Usman Bin Wilayat (College of Electrical and Mechanical Engineering (CEME), NUST, 2022)
    The ever-growing advancement in science has led humans to make their everyday tasks easy and fast. One of the key reasons for achieving milestones in this process was the development of robots, an ideal tireless worker. ...
  • Design & Fabrication of All-Terrain 6WD Robot 
    Project Supervisor: Dr. Sajid Ullah Butt Co-Project Supervisor Dr. Rehan Khan, Abdul Rehman Khan Azmat Hussain Danyal Shakir Usama Ali (College of Electrical and Mechanical Engineering (CEME), NUST, 2022)
    One of the difficulties in operating an autonomous robot through various terrains is the robot's incapacity to adapt to changing landscapes. Present wheeled and tracked vehicles can only access around half of the Earth's ...
  • Sun Tracking Solar System 
    Project Supervisor: Dr. Hasan Aftab Saeed CO-Supervisor: Asst. Prof. Yasser Riaz, Muhammad Usman Wakil Ahmad Tanveer Malik Adeeb Ur Rehman (College of Electrical and Mechanical Engineering (CEME), NUST, 2022)
    In Pakistan we have an enormous demand of electricity in domestic and commercial areas. This huge demand must meet daily needs in economical way for public at all levels. Energy demand depends on size of population and ...
  • Investigating The Effect of Infill Density and Pattern on Properties of 3D Prints 
    Project Supervisor: Dr. Muhammad Nasir Bashir, Yahya Saqib Mughal Raja Muaz Ali Muhammad Ahmer Ali (College of Electrical and Mechanical Engineering (CEME), NUST, 2022)
    Additive Manufacturing (AM) is buildup process which involves making three dimensional (3D) models in space from virtual Computer aided design (CAD) models by the help of 3D printer and software. Fused Deposition modelling ...

Search DSpace


Advanced Search

Browse

My Account